|
2. Configuration Parameters
These commands modify Pace ISDN TA configuration. The modifications are taken into account after a reset using the command ‘#Z’. The list of configurable parameters of interest is highly dependent upon software release. The list below gives a listi of the various parameters. Use AT#H1, AT#I, AT#V, AT#L... to list all the possible configuration parameters :
#HELP, #H Display list of configuration commands
#LOCAL_NUMBER Local ISDN number
#LOCAL_SUB_ADDRESS Local ISDN subaddress
Examples : AT#local_number="123" AT#local_number?
Global Parameters
|
Parameter Identification |
Parameter Short Form |
Description |
|
COUNTRY_CODE |
co |
Country code dependent on the variants which are in the code version:
1: North America
33: France
44: UK
49: Germany
1000: Europe (EuroISDN) |
|
NO_POWER_DETECTION |
nopower |
ISDN line power detection:
1: Disable
0: Enable |
|
A_LAW |
a |
Codec audio law
1: A-law
0: Mu-law |
|
NB_CALLS |
ncalls |
Maximum number of simultaneous calls (1..2) |
|
LOCAL_NUMBER |
nb |
Local ISDN number for outgoing calls (23 digits) |
|
LOCAL_SUB_ADDRESS |
sa |
Local ISDN subaddress for outgoing calls (4 digits) |
|
TEI_PAD |
tei1 |
Manual TEI for PAD D-channel (1..63) default=1 |
|
TEI_RELAY |
tei2 |
Manual TEI for X.25 synchronous D-relay (LAPB/LAPD) (1..63), default = 2 |
DTE channel 1: Asynchronous transparent using PAD to PAD rate adaptation
|
LOCAL_NB_ASYN |
nbasyn |
local ISDN number (4 digits) |
|
LOCAL_SUB_ADD_ASYN |
saasyn |
local ISDN subaddress (4 digits) |
|
INC_PRIORITY_ASYN |
ipasyn |
priority for incoming calls (0: Highest, 255: Disable) |
DTE channel 7: Asynchronous/Synchronous Conversion (PPP)
|
LOCAL_NB_PPP |
nbppp |
local ISDN number (4 digits) |
|
LOCAL_SUB_ADD_PPP |
sappp |
local ISDN subaddress (4 digits) |
|
INC_PRIORITY_PPP |
ipppp |
priority for incoming calls (0: Highest, 255: Disable) |
DTE channel 8: V.14 Asynchronous/Synchronous Rate Adaptation
|
LOCAL_NB_V14 |
nbv14 |
local ISDN number (4 digits) |
|
LOCAL_SUB_ADD_V14 |
sav14 |
local ISDN subaddress (4 digits) |
|
INC_PRIORITY_V14 |
ipv14 |
priority for incoming calls (0: Highest, 255: Disable) |
|
T_ORG_V14 |
tov14 |
Synchronisation delay V.14: Originator (ms) |
|
T_ANS_V14 |
tav14 |
Synchronisation delay V.14: Answerer (ms) |
DTE channel 10: Asynchronous V.120 Rate Adaptation
|
LOCAL_NB_V120 |
nbv120 |
local ISDN number (4 digits) |
|
LOCAL_SUB_ADD_V120 |
sav120 |
local ISDN subaddress (4 digits) |
|
INC_PRIORITY_V120 |
ipv120 |
priority for incoming calls (0: Highest, 255: Disable) |
|
V120_FRAME_SIZE |
fsv120 |
V.120 information field size |
DTE channel 13: 2 B-Channel Aggregation using Asynchronous V.120 Rate Adaptation
If DTE rate = 230.4 kbps, autobaud should be set to off before establishing the call by setting S114.
|
LOCAL_NB_2B |
nb2b |
local ISDN number (4 digits) |
|
LOCAL_SUB_ADD_2B |
sa2b |
local ISDN subaddress (4 digits) |
|
INC_PRIORITY_2B |
ip2b |
priority for incoming calls (0: Highest, 255: Disable) |
DTE channel 11: X.25 PAD/VideoPAD in B-Channel
|
LOCAL_NB_PAD_B |
nbpadb |
local ISDN number (4 digits) |
|
LOCAL_SUB_ADD_PAD_B |
sapadb |
local ISDN subaddress (4 digits) |
|
PRIORITY_PAD_B |
ippadb |
PAD priority for incoming calls (0: Highest, 255: Disable) |
|
INC_PRIORITY_VIDEO_B |
|
VideoPAD priority for incoming calls (0: Highest, 255: Disable) |
DTE channel 6: Telephony (for test)
|
LOCAL_NB_TEL |
nbtel |
local ISDN number (4 digits) |
|
LOCAL_SUB_ADD_TEL |
satel |
local ISDN subaddress (4 digits) |
|
INC_PRIORITY_TEL |
iptel |
Priority for incoming calls (0: Highest, 255: Disable) |
DTE channel 12: X.25 PAD in D-Channel
|
X25_ADDR_PAD_D_1 |
adx251 |
local X.25 address for PAD-D, (2 digits) |
|
ProfD |
ProfD |
PAD-D profile, (2 characters) |
|
DEFAULT_DTE_CHANNEL |
ch |
Default DTE channel (see .ATI5 ) |
X.25 Profile for Point to Point Communication in B Channel
|
DTE_DTE_PACKET_SIZE |
ps |
Packet size (16..1024), default = 1024 |
|
DTE_DTE_WINDOW_SIZE |
pws |
Packet window size (1..7), default = 3 |
|
DTE_DTE_LCN |
lcn |
Logical channel number (0..4095), default = 1 |
|
DTE_DTE_FRAME_WINDOW |
fsw |
Frame window size (1..7), default = 3 |
|
DTE_DTE_FRAME_T1 |
t1 |
Frame repetition timer (T200) in ms, default = 400 ms |
X.25 Profile for PSDN Access Across B-Channel Gateway
|
B_DTE_DCE_PACKET_SIZE |
psb |
Packet size (16..1024), default = 128 |
|
B_DTE_DCE_WINDOW_SIZE |
pwsb |
Packet window size (1..7), default = 2 |
|
B_DTE_DCE_LCN |
lcnb |
Logical channel number (0..4095), default = 1 |
|
B_DTE_DCE_FRAME_WINDOW |
fswb |
Frame window size (1..7), default = 3 |
|
B_DTE_DCE_FRAME_T1 |
t1b |
Frame repetition timer (T200) in ms, default = 400 ms |
Analogue Telephone Ports (POTS)
|
LOCAL_NB_POTS1 |
nbpots1 |
local ISDN number (4 digits) |
|
LOCAL_SUB_POTS1 |
sapots1 |
local ISDN subaddress (4 digits) |
|
INC_PRIORITY_POTS1 |
ippots1 |
priority for incoming calls (0: Highest, 255: Disable) |
|
LOCAL_NB_POTS2 |
nbpots2 |
local ISDN number (4 digits) |
|
LOCAL_SUB_POTS2 |
sapots2 |
local ISDN subaddress (4 digits) |
|
INC_PRIORITY_POTS2 |
ippots2 |
priority for incoming calls (0: Highest, 255: Disable) |
PAD Parameter
|
PAD_BANNER |
ban |
PAD banner: 0 = empty, 1 = transpac "TRANSPAC" |
|
